How to Build a Cheap Solar Heater With Recycled Aluminum Cans

http://diy-solar-power.net/how-build-cheap-solar-heater-recycled-aluminum-cans

Building a solar panel heater out of aluminum cans is not as far-fetched as you might think. A company in Canada, Cansolair, Inc., specializes in building these units and has won awards for their design. Their heaters have been described as "green energy and recycling all rolled into one", and have proven to be very cost effective and efficient as well.
How They Work

The units are typically installed on the outside walls of houses, and of course, in a location that gets a lot of sun. The idea is to draw air from near the floor of any room in a home, and pass it through the heating panel, which contains several columns of cans. The air is then returned to the same room near the ceiling. The cans are stacked and have large holes cut in both ends to allow the air to pass inside them while the outside of the cans is getting hot from the sun.
What You’ll Need

* 240 aluminum cans.
* 3 - 8 ft. 2x4s
* 4 ft. x 8 ft. x 1/2 in. sheet of plywood
* High Temperature Silicon
* 4 ft. x 8 ft. sheet of Plexiglas or Lexan
* A can of heat-resistant flat black spray paint.
* Plastic tubing
* Drill Press with wide drill bits
* Screws
* Optional Air Blower (consider a solar-powered unit)

Frame with some cans placed inside.



Bottom of frame. We used a vacuum cleaner attachment as a "manifold" to help distribute the air.



Top of frame showing hose that carries warmed air back into building.
How To Construct the Solar Panel

1. Construct a wooden frame out the the 2x4s, approx. 4 ft. wide x 8 ft. high x 3 1/2 in. deep. Next cut a piece of plywood this size and nail it to the back of the frame.
2. Drill a hole in the top center of the frame - this is where you'll connect your outlet hose.
3. Drill a hole in the bottom of the frame - this is where your inlet hose will be connected.
4. Drill large holes in the tops and bottoms from all the cans except for 16 which will be on the bottom row. For those, drill the holes in the tops and sides. Caution! Aluminum cans are sharp - use heavy work gloves or other means to hold them in place as you cut the hols out.
5. Start placing your cans into the frame. Create 16 columns of 15 cans each. Stack them one at at time, sealing them together as you go along. Make sure the ones with side holes are on the bottom row. Allow the silicone sealant to cure.
6. Spray the cans and frame with the heat-resistant flat black paint.
7. Cover the frame with the sheet of Plexiglas or Lexan.
8. Cut holes in the side of the building that line up with holes in the top and bottom of the solar panel. Air will be drawn from the building through the lower hole, which should be just above floor level, and be returned through the upper hole.
9. Mount the completed panel on the exterior wall of the home. Alternatively, you might mount the panel in a separate frame that will allow it to be tilted more toward the sun for better exposure.
10. Install the blower at either the inlet or outlet. This is not essential, but will increase the efficiency of your solar heater.

This unit allows air to flow all around the cans as it moves through the panel. A more efficient design will force all the air through the inside of the cans. This will also avoid exposure of the air to the black paint.
These might be helpful for you:

Also look here and here for more information.



* Add new comment

im going to try this but i
Submitted by Visitor on Thu, 11/05/2009 - 18:34.

im going to try this but i have two questions.1)will plastic bottles work in place of cans? 2)i have an old sliding door could that glass be used?

* reply

Plastic probably won't work
Submitted by rivulguy on Wed, 12/02/2009 - 14:00.

Sorry for the slow response. Plastic probably won't work. You need the heat transfer properties of aluminum in order for the unit to be efficient. Using glass is fine.